This is an old revision of the document!


Preparations

Attention: Running the reprap with wrong parameters may inflict serious damage to the extruder or the base plate!

To get reliable prints you have to find out the correct parameters for your extruder and material. This includes the distance from the base plate, temperature and speed.

When running the extruder at a too low temperature may result in pressure building up inside the extruder. This can damage the ptfe tube beyond repair. You have to recalibrate the temperature settings for every new material you are using. Even the same type of material on different rolls may have different parameters.

To get some initial values to work with follow the instructions which can be found at the blog from bits from bytes.

See http://rapmanv3.blogspot.com/2009/05/extruder.html and http://rapmanv3.blogspot.com/2009/05/printing.html

A short summary:
Adjust the bed according to the instructions. When laying out the bed the nozzle should press the extruded plastic a bit onto the bed so it sticks good.

Using a sheet of paper is a good method to test the distance of the extruder head to the table. The head should move freely above the paper. If the head is too close the the table, the head can clog which results eventually in disaster. (ABS melting into the table, ptfe-tube expands and rips)

If you hear a clicking noise from the feeder assembly, don't just blindly tighten the screws, maybe something is wrong, either the temperature is too low, or the feeding speed is to high or the head is too close to the table.

To get a initial temperature to run with heat the extruder to the desired value. Then try to feed the plastic by hand. If you can produce some nice filament by hand fasten the clamps pressing the plastic to the shaft. We had some success using ABS at 240°C.

If you set a temperature that is too low you might damage the extruder by building up to much pressure. If you set a to high temperature the ptfe may fail.

Check if you can restart the machine reliably from a cold state.

Now you can try your first print which will be a “schnaps glas” 😉

The raft for the minimug is very strong. The first layer is printed out at 1/4 the normal speed producing a very thick filament. The next layers are printed at a faster speed.

Skeinforge

Schneider uploaded a skeinforge version including a .skeinforge directory with the parameters from the bfb blog and some of our temperatures.

It uses a setting of 246°C, 40rpm and 16mm/s. The temperature is higher as required as the software of the repman keeps the temperature ca. 5°C bellow.

Use this package at your own risk!

Repdist from Schneider

Printing

WARNING: It is absolutely necessary to restart the Repman after completing/aborting a print or else the repman might damage it self. Do this also when exiting the file chooser menu

For example the head might move into the base plate producing a hole 😞

Select the Print Object menu item and use the right up/down-Keys to choose a model to print.

There is some filament extruded while heating up. Remove this with some tweezers to before the head starts moving when it reaches the target temperature. This might be necessary again between layers.

Printed objects and configurations

Date Name Object Description Modeler/CAD weight Link to Thingiverse Configuration changes Pictures Comments Copies
11.06.2009 shot_export.bfb Bigger shot glass Blender n/a n/a Standard n/a Quite a good print. Only weak layer 1
11.06.2009 empire_state.bfb Empire Statebuilding n/a 10g http://www.thingiverse.com/thing:625 none todo good print 1
12.06.2009 key_export.bfb Handcuff Key / Vertical Blender ~3g n/a Standard n/a Extruder much too fast ⇒ not enough time for layer to get hard 1
12.06.2009 key_export.bfb Handcuff Key / Vertical Blender ~3g n/a Extruder speed: 8mm/s n/a slower extrusion, but forgot to set PWM feed accordingly ⇒ extruder tried to feed too much 1
12.06.2009 key_export.bfb Handcuff Key / Vertical Blender ~3g n/a Extruder speed: 8mm/s, Flowrate PWM: 180 n/a Quite good print. Only “beard” of key is not very hard 1
12.06.2009 meter_key_export.bfb Utility Meter Key n/a n/a http://www.thingiverse.com/thing:88 Standard http://www.thingiverse.com/thing:198 Good print 3
12.06.2009 Untitled_export.bfb Servoholder AOI 15g n/a none n/a 50mm x 60mm wraping is visible 1
13.06.2009 http://www.thingiverse.com/download:1429 Box lid n/a 10g http://www.thingiverse.com/thing:635 none n/a n/a 1
15.06.2009 kleinbottle from bfb-forum Kleinbottle n/a 14g - 9r n/a - 1
17.06.2009 pyramide with eye Illuminatenpyramide n/a 11g n/a 9r n/a - 1
17.06.2009 meter_key_export.bfb Utility Meter Key n/a 4g http://www.thingiverse.com/thing:88 9r n/a - 1
18.06.2009 key_diverse Handcuff Key / Optimized Blender + G-Code ~1g n/a G-Code Hacking involved. See bottom n/a n/a 4
20.06.2009 ScrBoxT.bfb, ScrBoxB.bfb Screwable Jewellery Box MetaCAD 20g http://www.thingiverse.com/thing:413 codec n/a Bottom sucks, 2nd top print is great. Screwing works anyway. 2
21.06.2009 meter_key_export.bfb Utility Meter Key n/a 4g http://www.thingiverse.com/thing:88 9r n/a - 1
27.06.2009 keyb5.bfb Handcuff Key n/a 1g n/a 9r-optimized epic fail n/a see calibration 1

Calibration

The aim of this calibration process is to find skeinforge parameters for a better print quality and to better understand the influence of those parameters.

With this first test series I'm trying to get watertight floors.

For this purpose I am using a very small mug shape I created in aoi, so printing does not take too long.

run parameter observations
1 schneiders refenzconfig floors are not tight enough; ok from side view; sometimes layers do not connect properly
2 “Extrusion Width over Thickness” erhöht von 1.5 auf 1.8 not much better
3 lowered “Feedrate” to 12.0 mm/s too low, ⇒ klicking ⇒ abort
4 “Feedrate” to 14mm/s no visible difference in the floor layers compared to “2:”

just realized something: in the doku of skeinforge-speed “extrusion fill density ratio”

"fillament diameter"/"extrusion width"/"layer thickness" should be ~0.82; right now its somewhere at 68

run parameter observations
5 Reset “Feedrate” to 16mm/s and “Extrusion Diameter over Thickness” 1.38 not much better
6 reduced feedrate to 8mm/s and Flowrate PWM to 250 much better, but a bit clicking in the first base layer
7 raised feedrate back to 16mm/s and Flowrate PWM to 480 and “Base Layer Thickness over Layer Thickness” to 0.5 further improvment, no clicking, raft: very thin first layer
8 raised FLowrate PWM to 520, raised “Base Layer Thickness over Layer Thickness” to 0.7 very thin in the first raft layer and clicking ⇒ aborted
9 feedrate 10, Flowrate PWM 300, “Extrusion Diameter over Thickness” 1.5 minimal improovement
10 “Base Infill Density” from 0.5 to 0.3, increased “Flowrate PWM” to 480 while printing best quality so far
11 “Base Infill Density”from 0.3 to 0.35 “Flowrate PWM” = 470 teh horrors!!1! WORST QUALITY SO FAR
12 “Base Infill Density”from 0.3 to 0.35;“Flowrate PWM” = 470; “Extrusion Width over Thickness” from1.8 to 1.1 tight layers, but less accuracy
13 “Layer Thickness” from 0.4 to 0.3; “Feedrate” from 16 to 19mm/s Best so far
14 “Extrusion Width Over Thickness” from 1.1 to 1.3 probably a bit too much
15 “Extrusion Width Over Thickness” back to 1.2 still not as tight as #13 bit more accurate
13b tried #13 settings on handcuff key epic fail: completely smeared object. Also the raft seems to be too low on the baseplate. Iggy readjusted baseplate after print. BTW: upper part not completely flat, could be a problem for larger/not centric objects

G-Code Hacking

Wer die komplette Kontrolle ueber die Hardware will, muss zum Maschinencode greifen, so war es immer, und so wird es immer sein 🙂 Wobei ein “Assembler” fuer G-Code schon gut waere. von Hand wirklich was am Modell editieren ist eine Qual - aber durchaus auch mit vi zu schaffen, fuer den Handschellenschluessel habe ich (ray) das bereits gemacht.

Aber vorsicht: wer hier wirklich z.B. an Koordinaten rumfuhrwerkt kann den Reprap gegen die Wand, das Objekt, sich selbst und ueberhaupt fahren. Komplette Selbstzerstoerung halte ich fuer umsetzbar… Und nein, die beiden Brandflecken in der Platform kommen nicht von mir!

Durchaus praxisnaeher als Aenderungen am 3D-Modell sind aber Aenderungen an manchen Parametern, hier erstmal die wichtigsten Infos:
G/M-Code Referenz von Bitsfrombytes M-Code Reference von reprap Generell steuern die G-Codes den Kopf, die M-Codes veraendern Parameter.

Z.B.: Raft mit hoeherer Temperatur plotten (damits am Boden haelt) als das Modell, die Temperatur regelt der Paramter M104. Das Raft erkennt man im Code leicht, es sind die ersten drei “Bloecke” von G1 Zeilen im File. Davor ist z.B. ein M104 S246.0, dannach dann noch zweimal - das ist die Stelle wo der Extruder in die Ecke faehrt und nochmal heizt. Aendert man die zweiten M104 (warum die doppelt ist weiss ich nicht wirklich) auf z.B. S235.0 kann man kuehler printen - z.B. wichtig wenn das Modell grosse Bruecken hat. ACHTUNG: bei geringerer Temperatur sollte man auch den Materialvorschub (M108) reduzieren, sonst kann der Druck im Extruder zu gross werden.

Bei meinem Schluessel habe ich das Raft jetzt auch in hoeherer Geschwindigkeit als das Objekt (geht einfach schneller und das Raft braucht die Praezision nicht), die Bewegung wird ueber den F Parameter am Ende jeder G1 Zeile bestimmt. Wieder ACHTUNG: den Materialvorschub muss man auch hier wieder an die Geschwindigkeit anpassen. Grob sollte wohl gelten: doppelte Geschwindigkeit, doppelte Materialmenge.

Ebenfalls machbar: nach dem Printen des Rafts den Extrueder erst “aus dem Weg” bringen, so dass er beim Fahren in die Ecke den Wurstrest nicht gerade quer unter das Objekt legt… Und wohl auch vorher noch ne kleine Ehrenrunde fahren ehe man weiterplottet, hab ich aber noch nicht gemacht.

Beobachtungen:

  • M104 aendert eben nicht nur die Temperatur sondern faehrt auch in die Ecke bis die neue Temperatur erreicht ist. Das ist eigentlich schade, an den Bedienelementen des RepMan kann man die Temperatur auch “live” aendern, und ich hatte eine RepRap G-Code Doku auch mal so verstanden, dass es dafuer zwei M-Codes gaebe, einen mit “dwell” und einen ohne. Wo ist der Source?!?
  • M103/M101 schalten den Materialvorschub aus und an. Allerdings laeuft immer noch bischen was nach. Hardcore-Tuner koennten evtl. bei “Spruengen” die letzten “Striche” vor dem Sprung langsamer mit bereits abgeschaltetem Vorschub ziehen um sauberere Raender zu erreichen. Werde ich wohl mal testen…
  • M108 aendert den Materialvorschub, das kann man durchaus auch mitten im Print machen! Allerdings wird er im Display des RepMan nicht immer upgedated - wohl ein Bug. Ich *glaube* nachgeprueft zu haben dass es aber nur ein Fehler im Display ist, sollte man vor extremen Versuchen aber nochmal verifizieren. Und dann mal reporten!

Paramter:

  • (ray) Mein Raft printe ich aktuell mit M108 S400.0, M104 S246.0 bei nem Speed von F960.0
  • (ray) brauchbare Schluessel habe ich jetzt z.B. mit M108 S210,9, M104 S240.0 und nem Speed von F480.0 geprinted. Allerdings habe ich aktuell noch nen suboptimalen Start unten (zieht sich leicht zusammen), muss ich evtl. noch mit dem Materialvorschub experimentieren. Besser ging das mit der hoeheren Temperatur, aber die erzeugt nen unsauberen Ueberhang im schluesselbart, und leider kann man aktuell eben nicht live aendern.
  • reprap/printing.1246143784.txt.gz
  • Last modified: 2021/04/18 12:33
  • (external edit)