Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
cam:x350 [2020/01/12 16:03] – 9r | cam:x350 [2022/01/06 09:20] – [Timeline] 9r | ||
---|---|---|---|
Line 33: | Line 33: | ||
* Motioncontroller: | * Motioncontroller: | ||
- | * Steppertreiber: ? | + | * {{ :cam: |
- | * Stepper: | + | * ISP-Connector über dem MicroSDCardSplot, |
- | * X: ? | + | * Steppertreiber: |
- | * Y1: ? | + | |
- | * Y2: ? | + | * Default Microstepping: |
- | * Z: ? | + | * X: M1H M2L M3H = 32 |
- | * E: ? | + | * Y: M1H M2L M3H = 32 |
+ | * Z: M1L M2L M3H = 16 | ||
+ | * E: M1L M2L M3H = 16 | ||
===Pinbelegung | ===Pinbelegung | ||
ToDo | ToDo | ||
+ | |||
+ | ==Software | ||
+ | |||
+ | ===Repetierhost firmware dumps | ||
+ | |||
+ | https:// | ||
= Bedienung | = Bedienung | ||
Line 58: | Line 66: | ||
= Slicing | = Slicing | ||
- | == Slic3r | + | Konfiguration und Slicing-Profile für alle 3D-Drucker im Club: [[https:// |
- | [[https://github.com/muccc/reprap-x350-slic3r-profile]] Status: Working, but can be improved. | + | Slic3r/ |
- | == Cura | + | Cura: tbd |
- | tbd | ||
- | |||
- | == Prusa Slicer | ||
- | |||
- | tbd | ||
== allgemeine Druckparameter | == allgemeine Druckparameter | ||
Line 81: | Line 84: | ||
= Wartung | = Wartung | ||
- | == Filamentwechsel | + | ==Filamentwechsel |
tbd | tbd | ||
- | == Bed Leveling | + | ==Bed Leveling |
tbd | tbd | ||
- | == Octopi-Fallback | + | ==Octopi-Fallback |
Unter der rechten Gehäuseabdeckung befindet sich der mitgelieferte Raspberry Pi 2b inkl. SD-Karte mit Octoprint. | Unter der rechten Gehäuseabdeckung befindet sich der mitgelieferte Raspberry Pi 2b inkl. SD-Karte mit Octoprint. | ||
Line 99: | Line 102: | ||
- | == Neuer Raspberry3b | + | ==Neuer Raspberry3b |
| | ||
Line 122: | Line 125: | ||
* gzip' | * gzip' | ||
- | = Modifikationen | + | =Modifikationen |
- | == durchgeführt | + | ==durchgeführt |
* 2019/09/15: Update Pi (2b -> 3b) und Neuinstallation Octoprint | * 2019/09/15: Update Pi (2b -> 3b) und Neuinstallation Octoprint | ||
| | ||
- | == geplant | + | ==geplant |
- | === Firmware Update | + | ===Firmware Update |
- | === ws2812 Statusanzeige | + | |
- | === zweiter Extruder | + | https:// |
+ | |||
+ | ===Neuer Motioncontroller | ||
+ | |||
+ | ====Kandidaten | ||
+ | =====ARM 32bit | ||
+ | |||
+ | - BIGTREETECH SKR1.3/ | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | =====AtMega 8bit | ||
+ | |||
+ | - [[https:// | ||
+ | |||
+ | ===ws2812 Statusanzeige | ||
+ | |||
+ | ===zweiter Extruder | ||
====Aufbauskizze | ====Aufbauskizze | ||
Line 139: | Line 157: | ||
{{: | {{: | ||
- | ====Partliste | + | ====Teileliste |
^ Anzahl ^ Was ^ Note ^ bestellt^ | ^ Anzahl ^ Was ^ Note ^ bestellt^ | ||
Line 150: | Line 168: | ||
| 2 | [[https:// | | 2 | [[https:// | ||
| 2 | [[https:// | | 2 | [[https:// | ||
- | | 1 | NEMA Stepper | + | | 1 | NEMA17 |
+ | | 2 | [[https:// | ||
+ | | 2 | [[https:// | ||
== Timeline | == Timeline | ||
+ | * 2022/01/05: Remove 1st Extruder, build 2nd Hotend, update octoprint | ||
+ | * 2021/08/27: Complete 2nd stepper wiring | ||
+ | * 2021/06/01: Started work on 2nd/new extruder | ||
+ | * 2021/05/01: Replace fried extruder stepper drivers with a4999 drivers | ||
+ | * 2021/04/01: Changed Firmware to klipper | ||
+ | * 2020/01/20: Externe Raspi Spannungsversorgung mit Sockelleiste anbinden | ||
+ | * 2020/01/20: apt update raspbian & update octoprint plugins | ||
* 2020/01/10: Planung/ | * 2020/01/10: Planung/ | ||
- | * 2020/ | + | * 2020/ |
* 2019/10/29: Updated Octoprint to v1.3.12 | * 2019/10/29: Updated Octoprint to v1.3.12 | ||
* 2019/10/03: Extruder demontiert, Verstopfung in Heatbreak beseitigt, montiert | * 2019/10/03: Extruder demontiert, Verstopfung in Heatbreak beseitigt, montiert |