Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
cam:x350 [2020/01/31 18:12] – [Hardware] 9r | cam:x350 [2021/04/29 08:21] – [Hardware] 9r | ||
---|---|---|---|
Line 33: | Line 33: | ||
* Motioncontroller: | * Motioncontroller: | ||
+ | * {{ : | ||
* ISP-Connector über dem MicroSDCardSplot, | * ISP-Connector über dem MicroSDCardSplot, | ||
- | * Steppertreiber: | + | * Steppertreiber: |
- | * Stepper: | + | |
- | * X: ? | + | * Default Microstepping: |
- | * Y1: ? | + | * X: M1H M2L M3H = 32 |
- | * Y2: ? | + | * Y: M1H M2L M3H = 32 |
- | * Z: ? | + | * Z: M1L M2L M3H = 16 |
- | * E: ? | + | * E: M1L M2L M3H = 16 |
===Pinbelegung | ===Pinbelegung | ||
ToDo | ToDo | ||
+ | |||
+ | ==Software | ||
+ | |||
+ | ===Repetierhost firmware dumps | ||
+ | |||
+ | https:// | ||
= Bedienung | = Bedienung | ||
Line 77: | Line 84: | ||
= Wartung | = Wartung | ||
- | == Filamentwechsel | + | ==Filamentwechsel |
tbd | tbd | ||
- | == Bed Leveling | + | ==Bed Leveling |
tbd | tbd | ||
- | == Octopi-Fallback | + | ==Octopi-Fallback |
Unter der rechten Gehäuseabdeckung befindet sich der mitgelieferte Raspberry Pi 2b inkl. SD-Karte mit Octoprint. | Unter der rechten Gehäuseabdeckung befindet sich der mitgelieferte Raspberry Pi 2b inkl. SD-Karte mit Octoprint. | ||
Line 95: | Line 102: | ||
- | == Neuer Raspberry3b | + | ==Neuer Raspberry3b |
| | ||
Line 118: | Line 125: | ||
* gzip' | * gzip' | ||
- | = Modifikationen | + | =Modifikationen |
- | == durchgeführt | + | ==durchgeführt |
* 2019/09/15: Update Pi (2b -> 3b) und Neuinstallation Octoprint | * 2019/09/15: Update Pi (2b -> 3b) und Neuinstallation Octoprint | ||
| | ||
- | == geplant | + | ==geplant |
- | === Firmware Update | + | ===Firmware Update |
- | === ws2812 Statusanzeige | + | |
- | === zweiter Extruder | + | https:// |
+ | |||
+ | ===Neuer Motioncontroller | ||
+ | |||
+ | ====Kandidaten | ||
+ | =====ARM 32bit | ||
+ | |||
+ | - BIGTREETECH SKR1.3/ | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | =====AtMega 8bit | ||
+ | |||
+ | - [[https:// | ||
+ | |||
+ | ===ws2812 Statusanzeige | ||
+ | |||
+ | ===zweiter Extruder | ||
====Aufbauskizze | ====Aufbauskizze | ||
Line 149: | Line 171: | ||
| 2 | [[https:// | | 2 | [[https:// | ||
| 2 | [[https:// | | 2 | [[https:// | ||
+ | |||
== Timeline | == Timeline | ||