Table of Contents Eckdaten weitere Kosten Arbeitsaufwand: Was kann das Ding: bag content build bottom part top calibration reference Projekt: https://wiki.muc.ccc.de/geigercounter:startName: PiGi GeigercounterBeschreibung: Sammelbestellung: Board & Bauteile für PiGi Lizenz: --Beteiligt: 9R,Status: läuftKategorie: Hardware, SoftwareVerwandtes: Labor Geigercounter Eckdaten Preis für Board & einen einzeln teuer zu beschaffenden Poti: ~1,70€ weitere Kosten ~10€ für benötigte Bauteile >10€ für eine GeigerMüllerZählrohr Mit ~30€ einsatz sollte sich damit also ein einfacher Geigerzähler bauenlassen. Arbeitsaufwand: anfängerfreundliches SMD-Löten Was kann das Ding: Das Board erzeugt die zum Betrieb des GMZ nötige Hochspannung & gibt beidetektierter Strahlung eine falling edge aus die von RasPi, Arduino,ESP* oder sonstwas weiterverarbeitet werden kann. Details auf der Projektseite kit bag content pc item content 1 GM-tube type SBM-20 http://www.gstube.com/data/2398/ 1 board - 1 green bag C1-4, T1-3, IC1, L1 1 clear bag R1-9, J1 build Below is a list of all parts with their marking and recommended solder order. Before you start building it, please make sure no parts are missing (compare content of bags in your kit to the list above) you have read and understood the documentation especially the hardware section bottom part # V1.1 Part/Value Package Marking Notes 1 D2 MMSD4148 black belt mark facing towards C4 2 C4 1nF 0805 green 3 R5 330 ohms 0805 orange 4 R4 100k 0805 light green 5 R6 220k 0805 red don't confuse with R1 6 R1 1k 0805 pink don't confuse with R6 7 R9 27k 0805 yellow 8 IC1 TLC555QDRQ1/ICM7555 SOIC-8 8 pins Case mark facing towards R6 9 T2 MMBT4401 SOT-23 black package , 3 pins 10 J1 0 Ohm 0805 yellow/violett can be solder bridged instead of placing part In the picture above the J1b is closed. This routes the output signal to Pin 7 (GPIO4) on the RaspberryPi. Alternatively, you can close J1a, which would output the signal to Pin 11 (GPIO17) top # V1.1 Part/Value Package Marking Notes 1 C5 330pF 0805 red/green 2 R7 1.5k 0805 grey 3 R8 100k 0805 light green default - see signals for alternative values 4 T3 MMBT4401 SOT-23 black package, 3 pins 5 C1 220uF/10V LowESR Aluminium Electrolytic Capacitor see BRD loose black mark towards open hardware logo (=rounded corners towards T3) 6 C2 Vishay MLCC 10nF/1kV 1206 black package, 2 lightbrown parts 7 C3 Vishay MLCC 10nF/1kV 1206 black package, 2 lightbrown parts 8 R2 KOA Thick Film 1M 0.25W 0.5% 1206 black 9 R3 KOA Thick Film 4.7M 0.25W 1% 1206 violet 10 D1 Vishay BYGM23 Fast Recovery Diode 1.5A/ 1000V/ 75ns DO-214AC (SMA) clear package mark towards R2 11 T1 STN0214 Bipolar NPN 1k2V SOT-223 black package 12 L1 Murata Shielded Inductor 15mH see BRD pink foam, 4 pins algin dot mark with dimple (above “1”) 13 R10 Bourns Trimmer 100R see BRD blue trimmer screw towards T1 * — R10a optional, with a fixed value instead of R10 0805 - 14 H1 Stacking Raspberry Pi Header 2×13 2.54mm - optional - not included in the kit calibration reference Aussenluftstrahlung München geigercounter/start.txt Last modified: 2021/04/18 12:35(external edit)